A socket with a double connector will provide the ability to simultaneously power two devices connected to separate electrical points. In addition, for each of them there is no need to pull the cable, and it’s more convenient to use due to the grouped arrangement.
Installation can be done without problems on your own, taking into account the recommendations we have provided. We are ready to share the intricacies of performing electrical work. We will tell and show you in detail how to connect a double outlet, how to equip a socket for an electric point and ensure safe operation.
The information offered for review is supplemented by step-by-step photo guides, visual illustrations and videos explaining the nuances of installing and connecting power devices.
Types of Double Outlets
The main elements of the electrical outlet are the external protective housing and the working part, including the base and contacts.
They are interconnected by screw terminals - clamps necessary for connecting the cable of electrical equipment.
The only drawback of dual sockets is that through them it is problematic to connect two high-power consumers simultaneously
There is an erroneous opinion that double sockets are identical to assembled or dual models and are several independent devices located close to each other, connected by loops.
If you are connecting a double outlet to one supply circuit, then the electrical work is carried out according to a scheme similar to connecting a single. The only difference is the series connection of two contact pairs within the wiring device
Technological progress does not stand still. Modern models are more advanced designs. In terms of nominal voltage and amperage, they are strikingly different from sockets that were ubiquitous in Soviet times.
For example, if in the old-style models the permissible current did not exceed 10A, then for modern wiring equipment this figure is 16A.
Each part of the double socket can be connected to a separate power circuit, if you first remove the brass jumper connecting them to the terminal
In fact, a double outlet has one clamp and several distribution strips. Due to this, the electric current is supplied to both outlets equally, but its level will be divided depending on the power of the devices powered from the network.
And therefore, replacing a failed old device with a new one, you should know its design features, which suggest certain nuances during installation.
The distance between the output contacts, as well as the diameter of the plug pins for modern models is greater than for traditional analogues, and is 4.8 mm instead of 4 mm
By modification, double sockets are classified into such main types:
- Open and closed execution. In closed models, the openings are hidden behind the curtains, which are shifted to the side when the device is turned on. Devices of this type are indispensable for homes where small children. The curtains only work when pressed simultaneously. Due to this, even with the deliberate insertion of a foreign object, nothing dangerous happens.
- Without grounding and with grounding contacts. In models of the second type, grounding contacts are output to the socket housing, which protect electrical appliances and the user from breaking currents that accidentally “exit” to the plastic housing.
- For installation in rooms with high humidity and installation on the street. Models of the first option are marked IP-44. They are equipped with a housing that protects the device from moisture. Outdoor installations are marked IP-55. Their high-strength enclosures are protected against dust and moisture.
Each type has a corresponding letter mark. For example: “A” indicates that it is an American double outlet, “B” indicates the presence of a grounding contact.
Depending on the type of execution and the material of manufacture, the devices are also divided into standard and polar, overhead and custom-made
Among the latest developments, programmed sockets are especially popular. Equipped with a timer, the devices turn on and off independently from the power supply after a specified time interval has elapsed.
The protective housing of modern outlets is made of heat-resistant unbreakable plastic. To enhance the decorative qualities, it is decorated with various inserts.
Due to the variety of design options, you can choose devices that will be invisible in the interior or, on the contrary, act as a worthy decoration
When planning to install a double outlet on their own, experts recommend choosing simple models without any modifications. Or, give preference to double sockets with a spring ejector plug. Such models are convenient in that they are equipped with springs that trigger when the plug is removed from the device.
In order to protect yourself, minimizing the risk of emergencies, it is worth choosing products from trusted manufacturers: Schneider electric, ABB, Legrand.
Features of mounting the device
The double socket has one socket with two separate terminal blocks and one mounting part for wires.
A double socket is a monoblock, consisting of two plug connectors, and therefore the scheme of its connection to one socket will be somewhat more complicated
If you wish, the arrangement of an electric point can be performed on your own, without resorting to the services of a master.
Using jumpers is allowed only on condition that it is planned to connect not too powerful devices to electrical points. When connecting powerful equipment, the masters recommend parallel connection of two outlets, creating a branch of wires to each point.
But in any case, to prevent emergency situations, the total load on this type of sockets should be no more than 16A.
If it is necessary to install a socket with two different socket outlets, niches for their installation will need to be pre-drilled with an electric drill, while maintaining the same distance between the holes.
Image Gallery
Photo from
Power line power outage
Separation of the front panel from the outlet mechanism
Preparing wiring for connecting the mechanism
Stripping the edges of the wires to connect
Connecting wires to a power outlet
Fixing the socket mechanism in the socket
Mounting the working part of the outlet in the socket
Installing the front panel of the outlet
Materials for connecting
The wire for connecting the electric point must be made of the same metal as the main cable. For example, when using an aluminum cable, the jumper must also be made of aluminum.
To ensure a uniform distribution of incoming electricity, the cable used for connection must have the same cross-section as the main wiring in the room
To install a double outlet, you also need:
- flat and Phillips screwdrivers;
- braid stripping tool;
- pliers;
- insulating tape.
For safety reasons in case of fire, it is recommended to lay any electrical wires in the corrugation. This solution is also convenient because it does not require punching the wall, and also simplifies the replacement of damaged wires during subsequent operation.
Dual Socket Installation Technology
Installing a double outlet in one socket requires certain preparatory steps. The first step is to determine the ownership of the wires, finding out where the phase and zero are.
The easiest way is to study the code marking of insulation:
- phase wire painted in red or brown (less often white or black);
- neutral has a white-blue or blue isolation;
- grounding always painted green-yellow.
The following article, which we advise you to familiarize yourself with, will be familiarized with the features of marking the conductors of the electric cable. But for greater reliability, it is better to play it safe by taking measurements.
An indispensable assistant in this matter will be an ordinary or electronic screwdriver equipped at the end with an indicator - a bulb or an LED detector
To determine the ownership of the wires, remove the cover from the failed device and, in turn, touch a screwdriver with a sensitive indicator to each exposed wire: on neutral, the light signal will be absent, and on the phase it will light up.
If the grounding wire is not provided in the house, installation work is slightly simplified.
Before proceeding with the arrangement of an electric point, it is necessary to de-energize the room. To do this, lower the levers of the circuit breakers on the shield, translating into the “off” position. At the installation location of the double outlet, it is recommended to check the voltage again.
If there is still current in the phase, this indicates that not all supply lines are still de-energized. Therefore, it is so important to turn off all machines before starting work, and not be limited only to those that control the wires going to the outlet.
A double socket with a protective contact is installed if the earthing system of a private house is arranged. In multi-storey buildings there is no sense in devices with grounding, because zeroing is done there
Wall Marking
The outlet is placed near the wire going in the wall or from the electrical distribution box. The location of the future device is outlined in pencil.
Before you put a double outlet with two "glasses", you must determine the distance between the drilled holes. To do this, mark the center of the first podrozetnik. This is the intersection point of the diagonals. By the same principle, the center of the second device is determined.
At a marked place in the wall, a recess of such dimensions is performed so that a glass fits freely into it - the internal case of the device
To drill holes in the wall itself, use a crown, the diameter of which is a couple of millimeters larger than the size of the purchased socket. If there should be no problems with a brick or plasterboard wall, then to drill a hole for installing the outlet in a concrete wall, you will have to set the shock mode on the puncher.
With the rules and technology for mounting podrozetniki in walls made of concrete and drywall, you will familiarize yourself with the material collected and systematized in our article.
The depth of the hole should be such that the "glass" does not protrude beyond the surface of the wall. Having drilled a niche, it is necessary to clean its middle. To do this, use a chisel and a hammer. Plaster without any difficulties can be knocked down with a chisel or screwdriver.
Wiring Outlets and Twisting Wires
This stage is very responsible and it is necessary to approach its implementation with all care and caution. The task of the wizard is to connect the supply wire to the contacts. To do this, from the junction box stretch the wire to a double outlet.
The socket itself, by unscrewing the fixing screws with a screwdriver, is disassembled into two components, separating the front panel from the mechanism
The previously installed crown must be replaced with a drill. The diameter of the drill should be slightly larger than the cross section of the wire supplied to the outlet or the diameter of the corrugated pipe, in the cavity of which the lead wire will lie. The ideal option is when the diameters of the drill and wire match.
The main wire is inserted through one of the mounting holes of the socket. And the auxiliary one is launched through the second hole.
The twisting of wires is performed directly in the "glass". Before performing work, the extreme one and a half centimeters of the ends are cleaned from the braid by a stripper - a tool that does not bite the wire.
For lack of such, you can use a sharp knife, first cutting them round the winding, and then carefully removing it from the wire. For ease of assembly, the edges of the cores are lifted up.
To extend the life of the outlet, the bare ends of the wires need to be soldered, or brass contact should be used. The second option is more successful, because it not only simplifies the subsequent use of the outlet, but also ensures high safety of the device.
When connecting the wires, it is impossible to tighten their ends in the terminals, since under the influence of large forces they can be damaged
When connecting an outlet with grounding, they are always guided by the wiring rule: on the right is the phase, on the left is neutral. The grounding cable is connected to the upper and central terminal of the device, equipped with protruding "antennae", which often protrude outside the device. The ground contact is fixed in the same way as phase and zero.
Do not attach phase and neutral to one plate, as this will cause a short circuit and damage to all wiring.
Having fixed the wires in the contact holes, unclench the "antennae", unscrewing them clockwise with the help of special bolts
After completing the installation of electrical connections, proceed to the installation of socket boxes.
The subtleties of mounting the socket
Podrozetniki with power cables attached to them are fixed using holders placed on the sides. They can be bundled with the device, or they will have to be purchased separately. There are also models that are not equipped with locking tabs, which are secured by screwing onto screws.
As the screws are twisted clockwise, the locking “paws” will diverge to the sides, digging firmly into the socket
But since the socket with the lever in the center experiences a double load, during operation the fasteners of the mechanism can become loose and weaken. When dropping out the rosettes, the wires are often exposed, which is fraught with emergencies.
To increase the reliability of fastening, craftsmen often use alabaster or cement mortar. To obtain a homogeneous dense mass, in a structure resembling sour cream, dry alabaster is mixed with water. But keep in mind that the material should be bred in small portions and you need to work with it quickly and accurately.
A mixture of alabaster is laid in the place where it is planned to install the undergrowth. So that the mixture adheres well to the surface, the inner edges of the hole should first be moistened with water.
Work with the installation of the internal part of the device should be carried out 20-30 minutes after laying the mixture so that it has time to “grasp” a little. Having hoisted the “glass” on the prepared place and having buried it in the mixture, level the position with the help of a level and a hammer.
When installing the socket, it is important to observe the vertical and horizontal position, applying a level in both planes for this
The resulting gaps between the wall and the fungus are filled with the remains of alabaster. Without waiting for the gypsum to acquire the desired strength, the influx is removed with a knife.
By placing the double outlet horizontally or vertically and giving the device a predetermined position, fix it with screws. If necessary, adjust the level of the work with the help of pliers.
When tightening the fixing screws, the main thing is not to overtighten them, otherwise, with a strong pressure, the front panel may simply crack or break
At the final stage, the front panel is applied from above and clamped with screws. The enchanting element will close the unsightly part of the outlet and protect it from accidental damage.
After completing the connection of the outlet, it remains only to turn on the machines and the residual current circuit breaker in the panel and test the operation of the wiring equipment. It is better to check the operation of the outlet when turning on inexpensive household appliances, such as a desk lamp. After all, the slightest mistake in the installation process can provoke a short circuit and "burnout" of household appliances.
Video # 1. The process of connecting the built-in dual outlet:
Video # 2. Instructions for those who want to independently connect the outlet:
If the quality of the installation is in doubt, consult a professional electrician for help. He will not only inspect the work and, if necessary, troubleshoot, but also dispel all your doubts about the safe operation of the device.
Those wishing to share their own experience in the field of electrical installation, useful recommendations or ask questions, we invite you to leave comments in the block below the text of the article.